Search filter

166 results found

Wiring Diagram FT4 A
Wiring diagram

Wiring Diagram FT4 A

Wiring diagram àà The RWA button FT4A/24 V DC is used for manual triggering in the event of a hazard (fire). àà Surface-mounted housing àà Switching power max. 100 mA at 24 V DC àà Current consumption LED … The RWA button must be installed in a clearly visible position in the stairwell or corridor and must not be concealed by an open door leaf. àà Der RWA-Taster darf nur in Verbindung mit GEZE-Notstromsteuerzentralen E 260 N (VdS), MBZ 300, THZ und THZ Comfort eingesetzt werden. àà Der Anschluss erfolgt gemäß dem Anschlussplan der Notstromsteuerzentrale. àà Die Leitungsverlegung und der Anschluss darf nur von einer zugelassenen Elektrofirma vorgenommen werden. XX Bestimmungen der örtlichen Feuerwehr beachten. XX Klebeschild mit Angabe der RWA-Taster-Nummer bauseits auf die Innenseite des RWA-Tasters kleben. XX RWA-Taster vor Bauschmutz schützen. àà The RWA button may only be used in combination with GEZE emergency power control units E 260 N (VdS), MBZ 300, THZ and THZ Comfort. àà Connection is made in accordance with the wiring diagram for the emergency power control unit. àà Laying and connection of cables may only be carried out by an approved electrician. XX Observe any conditions prescribed by the local fire brigade. XX Apply the sticker with details of the RWA button number onto the inside of the RWA button on site. XX Protect the RWA button from building dirt. Überwachungswiderstände aktiv, im letzten RWA-Taster der Reihe Monitoring resistors not active, in all predecessors in series Der RWA-Taster muss gut sichtbar im Treppenhaus oder Flur montiert werden und darf nicht durch einen offenen Türflügel verdeckt werden. Sicherheitshinweise / Safety instructions The illustration shows the RWA button with the door opened. ON Montage / Installation 162458-01 Connect the RWA button according to the wiring diagrams for the emergency power control unit used. Test function. Apply the label "SMOKE VENT" in the desired language. After the successful function test, open the door of the RWA button and remove the card cover from behind the glass pane.

PDF | 1 MB
Wiring diagram RWA FT4 K
Wiring diagram

Wiring diagram RWA FT4 K

Wiring diagram FT4 K 24 V DC SMOKE VENT 136257-01 Symbols and illustrations Important information and technical notes are emphasised in order to illustrate the correct operation. Symbol Meaning means "important note"; information on avoiding material damage, understanding a concept or optimising working processes means "additional information" XX 1.4m 0.2m Symbol for an action: Here you have to do something. XX Observe the sequence if there are several action steps. Safety instructions àà The RWA button may only be used in combination with GEZE emergency power control units E 260 N (VdS), MBZ 300, THZ and THZ Comfort. àà Connection is made in accordance with the wiring diagram for the emergency power control unit. àà Laying and connection of cables may only be carried out by an approved electrician. XX Observe any conditions prescribed by the local fire brigade. XX Apply the sticker with details of the RWA button number onto the inside of the RWA button on site. XX Protect the RWA button from building dirt. XX Attach the wiring diagram in the RWA button. … with shield Sticker "Smoke vent" Initial operation XX XX XX XX Connect the RWA button according to the wiring diagrams for the emergency power control unit used. Test function. Apply the "Smoke vent" sticker in the required language. After the successful function test, open the door of the RWA button and remove the card cover from behind the glass pane. Connection and inner circuit XX The illustration shows the RWA button with the door opened. OPEN OPEN RWA button

PDF | 373 KB
Wiring diagram FT 4 A Acoustic
Wiring diagram

Wiring diagram FT

Wiring diagram àà àà àà àà àà àà àà Stromaufnahme Signalgeber max. 2,5 mA bei 24 V Signallautstärke ca. 60 dB(A) Glasscheibe auswechselbar –10 °C ...+55 °C nur für trockene Räume max. … 7 Montage / Installation Der RWA-Taster muss gut sichtbar im Treppenhaus oder Flur montiert werden und darf nicht durch einen offenen Türflügel verdeckt werden. 195730-00 Connect the RWA button according to the wiring diagrams for the emergency power control unit used. Set DIP switches S3 and S4 according to the required function. Test function. Apply the label "SMOKE VENT" in the desired language. After the successful function test, open the door of the RWA button and remove the card cover from behind the glass pane. … The RWA button must be installed in a clearly visible position in the stairwell or corridor and must not be concealed by an open door leaf. Sicherheitshinweise / Safety instructions àà Der RWA-Taster darf nur in Verbindung mit GEZE-Notstromsteuerzentralen E 260 N (VdS), MBZ 300, THZ und THZ Comfort eingesetzt werden. àà Der Anschluss erfolgt gemäß dem Anschlussplan der Notstromsteuerzentrale. àà Die Leitungsverlegung und der Anschluss darf nur von einer zugelassenen Elektrofirma vorgenommen werden. XX Bestimmungen der örtlichen Feuerwehr beachten. XX Klebeschild mit Angabe der RWA-Taster-Nummer bauseits auf die Innenseite des RWA-Tasters kleben. XX RWA-Taster vor Bauschmutz schützen. àà The RWA button may only be used in combination with GEZE emergency power control units E 260 N (VdS), MBZ 300, THZ and THZ Comfort. àà Connection is made in accordance with the wiring diagram for the emergency power control unit. àà Laying and connection of cables may only be carried out by an approved electrician. XX Observe any conditions prescribed by the local fire brigade. XX Apply the sticker with details of the RWA button number onto the inside of the RWA button on site. XX Protect the RWA button from building dirt. Kurzbeschreibung / Brief description àà Der RWA-Taster FT4 A/24 V DC dient zur manuellen Auslösung bei Gefahr (Feuer). àà Der RWA-Taster hat einen integrierten Signalgeber zur akustischen Signalisierung bei Alarm und/oder Störung àà Die akustische Signalisierung ist über DIP-Schalter abschaltbar àà Aufputzgehäuse àà Schaltleistung max. 100 mA bei 24 V DC àà Stromaufnahme LED 2,5 mA bei 24 V

PDF | 741 KB
Wiring diagram – FA GC 150 hold-open system
Wiring diagram

Wiring diagram – FA GC 150 hold-open system

Wiring diagram  GEZE hold-open system FA GC 150 Contents … Wiring diagram … 36 Wireless ceiling-mounted detector GC 172 or GC 173 – manual trigger switch or fire detector contact wired … .13 Wireless ceiling-mounted detector wired – wireless input modules GC 175 … Wiring diagram úú úú úú úú úú úú úú úú … Wiring diagram Note the requirements for selection and installation of the fire detectors and manual trigger switches in chapter … 29 Wiring diagram … 30 GEZE hold-open system FA GC 150 German institute for construction technology Wiring diagram Ceiling-mounted detectors GC 152 and GC 153 with line monitoring The general construction technique permit requires the cable to the ceiling-mounted detectors to be monitored. Line monitoring is active if: úú jumper J3 of the lintel-mounted smoke switch to the measuring chamber is set (2-3 factory setting, see chap. … 31 Wiring diagram GEZE hold-open system FA GC 150 Connection of a ceiling-mounted thermal detector GC 153 as a lintel-mounted detector and two further ceiling-mounted detectors PLEASE NOTE When two floor springs TS 550 E are used, no more than two ceiling-mounted detectors may be connected. … .2 Wiring diagram Ceiling-mounted smoke detector ORS 142 The ceiling-mounted detector ORS 142 is made up of the smoke detector ORS 142 and the base ORS 143 A. Ceiling-mounted smoke detector kit ORS 142 with úú … 33 Wiring diagram … .2 Wiring diagram Contact to the fire alarm system XX When a potential-free contact of the fire alarm system is connected, remove jumper J1 from the lintel-mounted smoke switch. Line monitoring is active if: úú jumper J3 of the lintel-mounted smoke switch to the measuring chamber is set (2-3, see chap. … The cable to the potential-free contact (fire-alarm system) must be laid separately or protected. 35 Wiring diagram … Wireless ceiling-mounted detector wired – wireless input modules GC 175 … .3 Wireless ceiling-mounted detector GC 172 or GC 173 – manual trigger switch or fire detector contact wired … .2 Wiring diagram GEZE hold-open system FA GC 150 Fig. … m 37 Wiring diagram … .3 German institute for construction technology Wiring diagram Contact of the fire alarm system and manual trigger switch UTA The general construction technique permit requires line monitoring to the potential-free contact of the fire alarm system and to the manual trigger switch. Line monitoring is active if: úú a … ), úú a 43 kΩ resistor is connected in parallel at both lintel-mounted smoke switches directly at the alarm output. 39 Wiring diagram GEZE hold-open system FA GC 150 … 40 GEZE hold-open system FA GC 150 Wiring diagram Door closer TS 4000 E-IS Door leaf installation úú Connector box with plug-in drip loop, ID 052105 GC 151 Connector box TS 4000 E-IS Door transmission Active leaf … 41 Wiring diagram GEZE hold-open system FA GC 150 E-ISM guide rail, E-ISM guide rail Boxer (E-ISM/G no hold-open function in the passive leaf, E-ISM/S no hold-open function in the active leaf) Connection board active leaf E hold-open device active leaf … 42 GEZE hold-open system FA GC 150 Wiring diagram Transom installation … 43 Wiring diagram GEZE hold-open system FA GC 150 Floor spring TS 550 E-IS úú Connection PCB, ID 001102 úú Terminal box on site Active leaf Passive leaf 24 VDC±10% Rem. w <20% 24 VDC±10% Rem. w <20% I=100 mA I=100 mA Switch closed if active leaf open Terminal box Connection board … GEZE hold-open system FA GC 150 Wiring diagram Hydraulic swing door drive TSA 160 NT F*, TSA 160 NT F EN7* Accessories TSA 160 NT F, ID 019654 Follow the wiring diagram for the TSA 160 NT swing door drive. … Hydraulic swing door drive TSA 160 NT F-IS* Accessories TSA 160 NT F, ID 019654 Follow the wiring diagram for the TSA 160 NT swing door drive. … 45 Wiring diagram GEZE hold-open system FA GC 150 Electromechanical swing door drive Slimdrive EMD F* Follow wiring diagram for the Slimdrive EMD swing door drive. … Electromechanical swing door drive Slimdrive EMD F-IS* Follow wiring diagram for the Slimdrive EMD swing door drive. … GEZE hold-open system FA GC 150 Wiring diagram Electromechanical swing door drive Powerturn F* Follow wiring diagram for the Powerturn swing door drive. … Follow wiring diagram for the Powerturn swing door drive. … 47 Wiring diagram GEZE hold-open system FA GC 150 Electromechanical swing door drive Powerturn F-IS/TS* Follow wiring diagram for the Powerturn swing door drive. … .4 Wiring diagram Hold-open system TS 5000 R Fig. … 49 Wiring diagram … GEZE hold-open system FA GC 150 Hold-open system Slimdrive EMD F/R Follow wiring diagram for the Slimdrive EMD swing door drive. … .9 Wiring diagram Fig. … 51 Wiring diagram GEZE hold-open system FA GC 150 … .10 Hold-open system Slimdrive EMD F/R-IS* Follow wiring diagram for the Slimdrive EMD swing door drive. 55 24 V … .11 Hold-open system Powerturn F/R* Follow wiring diagram for the Powerturn swing door drive. 55 24 V … GEZE hold-open system FA GC 150 Wiring diagram … .12 Hold-open system Powerturn F/R-IS* Follow wiring diagram for the Powerturn swing door drive. 55 24 V … 53 Wiring diagram GEZE hold-open system FA GC 150 … .13 Hold-open system Powerturn F/R-IS/TS* Follow wiring diagram for the Powerturn swing door drive. 24 V

PDF | 11 MB
Wiring diagram FT 4 A Secondary unit
Wiring diagram

Wiring diagram FT

Wiring diagram àà àà àà àà àà àà àà Erstinbetriebnahme Aufputzgehäuse Schaltleistung max. 100 mA bei 24 V DC Stromaufnahme LED 2,5 mA bei 24 V Glasscheibe auswechselbar –10 °C ...+55 °C nur für trockene Räume Lieferbare Farbe: àà orange (RAL 2011) XX XX XX XX àà The RWA button FT4 A/24 V DC is used for manual triggering in the event of a hazard (fire). àà The RWA button is a secondary unit with only one display for alarm. àà Can only be used in combination with a main FT4 A button. àà Surface-mounted housing àà Switching power max. 100 mA at 24 V DC àà Current consumption LED … mA at 24 V àà Glass pane replaceable àà –10 °C ...+55 °C àà only for dry rooms àà Colour available: àà orange (RAL 2011) XX Initial operation RWA-Taster nach den Anschlussplänen der verwendeten Notstromsteuerzentrale anschließen. Funktion testen. Beschriftungsschild "RAUCHABZUG" in gewünschter Sprache anbringen (siehe nächste Seite). Nach erfolgreichem Funktionstest Tür des RWA-Tasters öffnen und Karton hinter der Glasscheibe entnehmen. Falls die Taste ZU/Reset nicht angeschlossen ist, Beschriftung „Reset“ (2) abkleben. Anschluss und Innenschaltung XX XX XX XX XX XX Connect the RWA button according to the wiring diagrams for the emergency power control unit used. Test function. Apply the label "SMOKE VENT" in the desired language. After the successful function test, open the door of the RWA button and remove the card cover from behind the glass pane. If the CLOSE/RESET switch is not connected, paste over the "Reset" label (2). Connection and inner circuit XX Die Darstellung zeigt den RWA-Taster mit geöffneter Tür. DIP-Schalter S3 (3) / DIP switch S3 (3): ON Überwachungswiderstände aktiv, im letzten RWA-Taster der Reihe … 126 Sicherheitshinweise / Safety instructions àà Der RWA-Taster darf nur in Verbindung mit GEZE-Notstromsteuerzentralen E 260 N (VdS), MBZ 300, THZ und THZ Comfort eingesetzt werden. àà Der Anschluss erfolgt gemäß dem Anschlussplan der Notstromsteuerzentrale. àà Die Leitungsverlegung und der Anschluss darf nur von einer zugelassenen Elektrofirma vorgenommen werden. XX Bestimmungen der örtlichen Feuerwehr und lokale Anforderungen an RWA-Taster beachten. XX Klebeschild mit Angabe der RWA-Taster-Nummer bauseits auf die Innenseite des RWA-Tasters kleben. XX RWA-Taster vor Bauschmutz schützen. àà The RWA button may only be used in combination with GEZE emergency power control units E 260 N (VdS), MBZ 300, THZ and THZ Comfort. àà Connection is made in accordance with the wiring diagram for the emergency power control unit. àà Laying and connection of cables may only be carried out by an approved electrician. XX Observe any conditions prescribed by the local fire brigade and observe local requirements for RWA buttons. XX Apply the sticker with details of the RWA button number onto the inside of the RWA button on site. XX Protect the RWA button from building dirt. Kurzbeschreibung / Brief description àà Der RWA-Taster FT4 A/24 V DC dient zur manuellen Auslösung bei Gefahr (Feuer). àà Der RWA Taster ist eine Nebenbedienstelle mit nur einer Anzeige für Alarm . àà Nur in Kombination mit einer Hauptbedienstelle FT4 A einsetzbar.

PDF | 594 KB
Wiring diagram heat detector GC 163 RWA
Wiring diagram

Wiring diagram heat detector GC 163 RWA

wiring diagram) Smoke detector connection Test Use heat detector testing device from a recognised manufacturer for testing in accordance with the manufacturer’s instructions. àà The red LED on the detector must change to the alarm state. àà An alarm must be activated on the RWA control unit. àà After the test has been completed, reset the alarm on the control unit and carry out a detector line reset.

PDF | 5 MB
Additional wiring diagram TSA 160 NT TANDEM
Wiring diagram

Additional wiring diagram TSA 160 NT TANDEM

diagram applies in addition to connection diagram DCU5, Mat. No. 125014. Two drives TSA 160 NT are mechanically connected to form a tandem drive. The safety and actuation units must be connected at the DCU5 Master Control unit. The DCU5 control units can be configured with the buttons S1 and S2 or by using the Display program switch. Configuration at the Master- und Slave-control unit: DCU5 Master DCU5 Slave EF = 01 SI = according to desired function SO = 01 TE = depending on the used sensor EF = 02 SI = 00 SO = 01 TE = 00

PDF | 135 KB
Wiring diagram Toplock CTI, CTI B TOPLOCK CTS V, CTS BV
Wiring diagram

Wiring diagram Toplock CTI, CTI B TOPLOCK CTS V, CTS BV

diagram code number keypad Toplock CTI, CTS 1/1 GEZE GmbH P.O. Box 1363 71226 Leonberg Germany GEZE GmbH Reinhold-Vöster-Str. 21-29 71229 Leonberg Germany Tel. +49 (0)71 52-203-0 Fax +49 (0)71 52-203-310 GEZE Online: www.geze.com GEZE Branches Germany GEZE GmbH Niederlassung Nord/Ost Bühringstr.8 13086 Berlin (Weissensee) Tel. +49(0)30-47 89 90-0 Fax. +49(0)30-47 89 90-17 E-Mail: berlin.de@geze.com GEZE GmbH Niederlassung West Nordsternstraße 65 45329 Essen Tel. +49(0)201-830 82-0 Fax. +49(0)201-830 82-20 E-Mail: essen.de@geze.com GEZE GmbH Niederlassung Mitte Adenauerallee

PDF | 180 KB
Block diagram OL 320
Installation drawing

Block diagram OL 320

DWG | 1 MB
Block diagram OL 90 N
Installation drawing

Block diagram OL 90 N

DWG | 1 MB